TRT test setup
Describe borehole geometry, construction, fluid, flow and heat input, ground heat capacity and undisturbed temperature. Match the measured test conditions and record their provenance. Fitting inputs and uncertainty estimates depend on these assumptions.
Step-by-step workflows · Menus and keyboard

| Control | Meaning / action | Unit | Range / choices | Example value |
|---|---|---|---|---|
| Copy borehole, pipes, fluid and ground from the project | Copy the design construction and material settings into this TRT setup; confirm they describe the measured test. | |||
| Length H: | Active length of the test borehole | m | 1 to 3000 | 150 |
| Buried depth D: | Depth of the top of the active length | m | 0 to 500 | 4 |
| Borehole diameter: | Borehole diameter (2 rb) | mm | 50 to 600 | 140 |
| Time since grouting: | Days between grouting and the start of the test (quality check) | days | -1 to 3650 | -1 |
| Pipe type: | Select one of the listed alternatives. | Single-U / Double-U / Triple-U / Coaxial / Multi-U (4–8) / Helix (spiral coil) | ||
| Pipe outer diameter: | Outer diameter of the pipes (coaxial: outer pipe) | mm | 10 to 200 | 32 |
| Pipe wall thickness: | Wall thickness of the pipes | mm | 0.5 to 20 | 2.9 |
| Shank spacing: | Centre-to-centre distance of opposite legs | mm | 0 to 300 | 70 |
| Grout conductivity: | Thermal conductivity of the grout | W/(m·K) | 0.1 to 10 | 1.6 |
| Pipe conductivity: | Thermal conductivity of the pipe wall | W/(m·K) | 0.05 to 60 | 0.42 |
| Fluid: | Select one of the listed alternatives. | Water / / Glycols / Monoethylene glycol (MEG) / Monopropylene glycol (MPG) / / Alcohols / Ethanol / Methanol / / Salt solutions / Potassium formate / Potassium acetate / Potassium carbonate / Calcium chloride / Sodium chloride / / Glycerol / / Custom (constant properties) / Table (temperature-dependent) | ||
| Mass fraction: | Mass fraction of the antifreeze | % | 0 to 60 | 25 |
| Heat capacity C: | Volumetric heat capacity of the ground: fixed in the evaluation unless it is estimated | MJ/(m³·K) | 0.5 to 5 | 2.2 |
| Surface temperature: | Mean ground surface temperature (T0 plausibility check) | °C | -20.1 to 40 | 9 |
| Geothermal heat flux: | Geothermal heat flux (T0 plausibility check) | W/m² | -0.005 to 0.3 | 0.06 |
| Method: | Select one of the listed alternatives. | Initial circulation (before the heating) / Manual value / Depth profile (mean over the active length) | ||
| Averaging window: | Averaging window before the heating start | min | 1 to 1440 | 20 |
| T0 (manual): | Undisturbed ground temperature | °C | -10.1 to 100 | -10.1 |
| Add depth | Add a depth-resolved TRT input row. | |||
| Remove depth | Remove the selected depth-resolved input row. | |||
| Power: | Q = ρ cp V̇ (Tin − Tout) with the fluid properties at the mean fluid temperature, or the heater / heat meter column | Measured (power column) / From flow and ΔT (inlet − outlet) | ||
| Heating start: | Start of the heating in the time of the data | h | -1000 to 10000 | 1 |
| Heating end: | End of the heating since its start; the recovery follows (automatic: the last sample with heating power) | h | -0.1 to 10000 | -0.1 |