The thermal plume is the change of the ground temperature against the undisturbed ground, , in the plan around the borehole field. Authorities and neighbours ask how far the cooled (or warmed) ground reaches, whether it crosses the property line, and when it reaches a well, a neighbouring field or a building. The Thermal plume page answers these questions at the end of every month of the design period, from the monthly base loads of the design, with isotherms for chosen thresholds (default ±3 K) and distance checks against the objects of the site plan.
Two sources give the field: the analytic plume of this chapter, which runs after every calculation, and the temperature field of the 3D finite-element analysis when it is available. Both are sampled on the same raster and evaluated by the same procedure.
21.1 Load convention
[W/m] is the base ground load of month per metre of borehole (> 0 heat injected): the monthly base load divided by the total length, or, with hourly loads, the mean of the hourly ground load over each 730-hour month. Month starts at h, and the map of month is at its end:
where is the response at the plan point to a unit step of 1 W/m in the field. The peak loads are not included: they act for hours and do not reach the far field.
21.2 Analytic response: finite and moving finite line sources
Every borehole is a line source over its active length with heat rate per metre. The receiver is the plan point averaged over the active depth range (from the shallowest top to the deepest bottom of the active lengths), or a short segment at a chosen depth. The response of an emitter at plan distance is the segment-to-segment finite line source (Eskilson 1987, in the form of Claesson & Javed 2011), with receiver length :
where is the axial part, which holds the emitter and receiver depth ranges and the mirror image above the ground surface. With groundwater flow the moving finite line source (Molina-Giraldo et al. 2011) is used:
with the Darcy velocity, and the volumetric heat capacities of the water and the saturated ground, and the distance of downstream of the emitter. The integral without the direction factor depends on only; it is tabulated, and the factor is applied per point, so neither part can overflow. The tables hold every month end on a logarithmic distance grid ; between the nodes is interpolated linearly in (error about relative).
- Inclined boreholes are split into pieces of at most 2 m in the plan; each piece is a vertical line source at the plan position of its midpoint over its vertical extent, with the heat of the piece kept. This also covers groundwater with inclined boreholes, as an approximation.
- Ground. The effective homogeneous ground of the design (thickness-weighted over the active length for layered ground) and the Darcy flux averaged over the active depth range, . With layers the page says so; the 3D plume resolves the layers.
21.3 Heat split between the boreholes
is the heat rate per metre of borehole relative to the field mean, :
- Uniform heat flux: , as the g-function.
- Uniform wall temperature: all walls at the same temperature with the finite line source response at the end of the period, for every , one dense linear system.
- Uniform fluid temperature: as above with ; the resistance evens the split out.
This is the long-time split. At early times the true split is more uniform (the boreholes do not interact yet); the difference concerns boreholes next to each other, not the far plume. Each borehole emits uniformly along its length. For a 3 × 2 field (6 m spacing, 100 m, 25 years) the corners take 1.07 and the middle boreholes 0.85 under a uniform wall temperature, 1.05 and 0.89 with = 0.1 m K/W under a uniform fluid temperature.
21.4 Superposition
Per emitter type and distance node, is a causal convolution over the months, done by the fast Fourier transform. Then, for every point and month ,
one table lookup per point and borehole. A raster of 250 × 90 cells around a 4 × 4 field over 25 years (300 months) with groundwater takes a few hundredths of a second, so the plume is recomputed after every calculation and for every change of the thresholds, the depth or the objects.
Window. The raster covers the boreholes, the property-line polygons and the evaluation objects, plus a margin of on every side ( the extent of these objects) and, with groundwater, twice that margin plus more downstream, as about 150 × 150 square cells. A region that touches the edge of the raster is flagged, and the window is enlarged by half its size on the sides concerned (up to three times) and sampled again, so the extents are not cut by the window.
21.5 Distance checks
The field is sampled at the cell centres and at points every 1 m or less along the objects. Then, for each threshold (cooling : the region ; warming : ):
- Isotherms by marching squares on the cell centres, joined into polylines.
- Area by bilinear interpolation between the cell centres, 4 × 4 samples per cell.
- Reach: the largest distance of the region's boundary from the field edge, the convex hull of the borehole traces in the plan (the heads and the plan positions of the bottoms). The dimension line runs from the nearest point of the hull.
- Downstream length and width (groundwater): the largest distance of the boundary beyond the field's downstream edge along the flow, and the extent of the boundary across the flow.
- Clearance to a property line (a closed boundary polygon): the smallest signed distance of the region's boundary to the polygon edge, positive inside. A negative value means that the region reaches beyond the property line by that much; the dimension line then runs from the edge to the farthest point outside.
- Clearance to a line or point object (a well, a pipe, a neighbouring borehole): the smallest distance between the region and the object when no sample of the object lies in the region; otherwise negative, the largest distance of an object sample inside the region from the isotherm.
- First crossing: the first month end at which a sample of the object is beyond the threshold.
- Time: the end of the period, a chosen month, or the worst moment, the month with the largest sum of the areas beyond all thresholds. Over the period the month of the largest area and of the largest reach are also reported.
The 3D source evaluates the finite-element temperature field of the 3D analysis at the same plan points, at 12 depths over the active depth range (averaged) or at the chosen depth, with the same load convention. The 2D and 3D maps of a month can therefore be compared and overlaid; outside the finite-element block there is no value.
21.6 Verification
The analytic plume was checked against an independent quadrature of the point-source integral along every borehole (finite and moving finite line source with the image above the surface), sampled on the same raster and evaluated by the same code, and against the 3D plume of the same project. Point values: within 0.18 % at a single depth and 0.09 % averaged over the depth for a single borehole over 25 years, within 0.5 % for seasonal loads and with groundwater, and +0.05 to +0.17 % for an inclined borehole. Table 33 shows isotherm extents for a constant extraction of 20 W/m (ground 2.5 W/(m K), 100 m boreholes, 25 years, at 54 m depth for the reference columns).
| Case | Isotherm | Quantity | Reference | Analytic plume | 3D plume |
|---|---|---|---|---|---|
| single borehole | −2 K | reach [m] | 8.57 | 8.57 | 8.45 |
| single borehole | −2 K | area [m²] | 230.6 | 230.6 | 223.1 |
| single borehole | −0.5 K | reach [m] | 32.79 | 32.79 | 32.58 |
| single borehole | −0.5 K | area [m²] | 3377 | 3377 | 3304 |
| 3 × 2 field, 6 m | −3 K | reach [m] | 29.66 | 29.66 | 29.21 |
| 3 × 2 field, 6 m | −3 K | area [m²] | 3414 | 3415 | 3356 |
| 3 × 2 field, 6 m | −0.5 K | reach [m] | 61.98 | 61.99 | 63.24 |
| 3 × 2 field, 6 m | −0.5 K | area [m²] | 13369 | 13372 | 13575 |
The analytic plume reproduces the reference to 0.01 m in every extent and to 0.1 % in the areas; the one exception is a region of 5 m² on cells of 1.1 m (strong groundwater flow), where the raster resolution gives −3 % area. The 3D plume lies within −4.3 to +2.0 % in reach and downstream length and −6.6 to +1.5 % in area of the analytic one: slightly smaller at the near isotherms and with groundwater, slightly larger at the far isotherms. No isotherm touched the edge of the raster in any case.
21.7 Limits
- Monthly base loads only; the hourly peaks are not in the map.
- The analytic plume uses the effective homogeneous ground and the long-time heat split, with every borehole emitting uniformly along its length; layered ground is resolved only by the 3D plume.
- The raster resolution (about 0.5–1 % of the window per cell) limits very small regions.
- The thresholds are the user's: the program checks no legal limits. Distances to neighbours, wells and protection zones are for the responsible authority to judge.